Jet 354401

General Purpose Drill Presses, Floor Drill Press, Drive Type Belt, Swing 20 in, Spindle Taper 3MT, Motor HP 1 1/2 hp, Capacity Steel 3/4 in, Capacity Cast Iron 1 in, Drilling Capacity Wood Not Specified, Includes Chuck with Key, Power Down Feed Included No, Voltage 115/230, Number of Speeds 12, Chuck Size 3/4 in, Spindle Speed 150 to 4200 rpm, Spindle Travel 4 5/8 in, Base Size 13-3/4 in x 22-3/4 in, Table Work Surface 18-1/2 in x 16 in, Hz 60, Phase 1, Number of T-Slots 6

General Purpose Drill Presses, Floor Drill Press, Drive Type Belt, Swing 20 in, Spindle Taper 3MT, Motor HP 1 hp, Capacity Steel 5/8 in, Capacity Cast Iron 3/4 in, Drilling Capacity Wood Not Specified, Includes Chuck with Key, Power Down Feed Included No, Voltage 115/230, Amps AC 9.0/4.5, Number of Speeds 12, Chuck Size 5/8 in, Spindle Speed 150 to 4200 rpm, Spindle Travel 4 3/4 in, Base Size 22-3/4 in x 17-3/4, Table Work Surface 15-1/2 in x 13-1/2 in, Hz 60, Phase 1, Number of T-Slots 3

General Purpose Drill Presses, Floor Drill Press, Drive Type Belt, Swing 16 7/8 in, Spindle Taper 2MT, Motor HP 3/4 hp, Capacity Steel 3/4 in, Capacity Cast Iron Not Specified, Drilling Capacity Wood 2 in, Power Down Feed Included No, Voltage 115, Number of Speeds 16, Chuck Size 5/8 in, Spindle Speed 210 to 3500 rpm, Spindle Travel 5 in, Base Size 20 in x 12-5/8 in, Table Work Surface 14 in x 19 in, Hz 60, Phase 1, Number of T-Slots 2, Table Slot Size 5/8 in, Column Dia. 3 5/32 in

General Purpose Drill Presses, Bench Drill Press, Drive Type Belt, Swing 10 in, Spindle Taper 33JT, Motor HP 1/3 hp, Capacity Steel 3/8 in, Capacity Cast Iron 1/2 in, Drilling Capacity Wood Not Specified, Includes Arbor, Chuck, Paddle Switch, Spindle Depth Stop, Tilting Table, Power Down Feed Included No, Voltage 120, Amps AC 4.1, Number of Speeds 5, Chuck Size 1/2 in, Spindle Speed 650 to 3070 rpm, Spindle Travel 2 1/2 in, Base Size 8-1/4 in x 13-1/2 in

Drill, Engine Brand Echo, Power Source Gas Powered, Fuel Tank Capacity 30.4 oz, Engine Displacement 22.54 cc/rev, Engine Type 2 Stroke, Fuel Mix Ratio 50:01:00, Fuel Type Gas, Horsepower 1.4 hp, Chuck Size 1/2 in, Drill Chuck Type Keyed, Chuck Material Steel, Max. Torque 12 ft-lb, Min. Torque 1 ft-lb, Overall Height 11 in, Overall Length 12 in, Overall Width 11 in, Throttle Type Trigger, Gear Reduction 17:1, Handle Type D-Handle, Handle Material Metal, Housing Material Poly

General Purpose Drill Presses, Bench Drill Press, Drive Type Belt, Swing 8 in, Spindle Taper 33JT, Motor HP 1/3 hp, Capacity Steel 1/2 in, Capacity Cast Iron 1/2 in, Drilling Capacity Wood Not Specified, Includes Chuck with Key, Power Down Feed Included No, Voltage 120, Amps AC 2.3, Number of Speeds 5, Chuck Size 1/2 in, Spindle Speed 750 to 3200 rpm, Spindle Travel 2 in, Base Size 7 in x 10-3/4 in, Table Work Surface 6-1/2 in x 6-1/2 in, Hz 60, Phase 1, Number of T-Slots 0

Accu-Fence System w/Riving Knife 64B,

Belt Drive Motor, Single Phase, Motor Design Split-Phase, 1/3 HP, Nameplate RPM 1, 725, No. of Speeds 1, Voltage 115V AC, 5.8 Full Load Amps, 48 Frame, 60 Hz, Motor Service Factor 1.35, Motor Thermal Protection Auto, Ins. Class B, Max. Ambient Temp. 40 Degrees C, Duty Cycle Continuous, Motor Shaft Rotation CW/CCW, Motor Enclosure Design Open Dripproof, Motor Mounting Type Cradle Base, Motor Mounting Position All Angle, Motor Frame Material Rolled Steel, Shaft Dia. 1/2 in, Shaft Length 1 1/2 in

Hydraulic Press, Pump Type Manual, Frame Type H-Frame, Frame Capacity 10 ton, Cylinder Type Single Acting

Rout-R-Lift

Air Cleaner Filters, 4-3/4x12x29 Nominal Filter Size, Nominal Height 9-1/2 in, Nominal Width 19-1/4 in, For Use With 18F218, Frame Included Yes, Filter Efficiency 0.99 Percent, Includes (2) Filters, Package Quantity 2