Packard Induced Draft Blowers

Induced Draft Furnace Blower, Voltage 208/230, 0.8 Amps, Height (In.) 4 1/4 in, Width (In.) 5 1/4 in, Depth (In.) 5 1/4 in, Gas Furnaces, Construction Material Metal Housing, Agency Compliance UL and CUL Recognized, Replaces Carrier HC24HE230, Product Used as Direct OEM Replacement Only. Any Other use Constitutes a Misapplication, Which Voids the Warranty and May Create Unsafe Conditions, Includes Gasket, Fits Brand Carrier, For Use With Mfr. Model Number HC24HE230

Induced Draft Furnace Blower, Replacement, Voltage 115, 1.20 Amps, 138 W Watts, Height (In.) 10 in, Width (In.) 6 7/8 in, Depth (In.) 6 1/2 in, Residential Furnaces, Construction Material Metal Housing, Agency Compliance UL, Replaces Lennox 47H12, LB-82590CA, Fits Brand Lennox, For Use With Mfr. Model Number 47H12, LB-82590CA

Draft Inducer, Replacement, Inlet and Outlet Dia. (In.) 5/2.75 x 1.75, Voltage 115, 1.00 Amps, 1/50 hp HP, Height (In.) 5 1/32 in, Width (In.) 7 7/64 in, Depth (In.) 7 43/64 in, Designed for Ventilation of Gas Furnace, Construction Material Steel, Agency Compliance CSA, Replaces Dunkirk 433-00-510, Fits Brand Dunkirk, For Use With Mfr. Model Number 433-00-510

Induced Draft Blower, High Temperature, Vent Pipe Dia. (In.) 4 or 6, Inlet and Outlet Dia. (In.) 4, Voltage 115, 1.26 Amps, 95 W Watts, Height (In.) 7 7/8 in, Width (In.) 11 in, Depth (In.) 7 in, Used for Side Wall Venting Commercial Natural Gas or LP Fired Equipment Including Boilers, Water Heaters and Unit Heaters, Construction Material Aluminized Steel Housing and Blower Wheel, Agency Compliance ETL Listed to UL378 and CAN3-B255-M81, View Catalog Page For Selection Criteria

Draft Inducer, In-line, Vent Pipe Dia. (In.) 8 to 12, Voltage 115, 5.4 Amps, 1/4 hp HP, Height (In.) 14 1/2 in, Width (In.) 13 1/2 in, Depth (In.) 8 3/4 in, 4 x 12-3/4 Cut Out Required, Provides Positive Draft for Smokepipe and Aids Proper Exhaust of Combustion Gas., Construction Material Aluminized Steel Housing and Blower Wheel, Agency Compliance -, Replaces -, View Catalog Page For Selection Criteria, Not Applicable, N/A, N/A., Not Applicable, Not Applicable, 590765850710, 603653615357

Induced Draft Blower, High Temperature, Vent Pipe Dia. (In.) 6 or 8, Inlet and Outlet Dia. (In.) 6, Voltage 115, 1.51 Amps, 224 W Watts, Height (In.) 9 1/4 in, Width (In.) 11 1/2 in, Depth (In.) 8 1/2 in, - Cut Out Required, Used for Side Wall Venting Commercial Natural Gas or LP Fired Equipment Including Boilers, Water Heaters and Unit Heaters., Construction Material Aluminized Steel Housing and Blower Wheel, Agency Compliance ETL Listed to UL378 and CAN3-B255-M81, Replaces -

Draft Inducer, In-line, Vent Pipe Dia. (In.) 5 to 8, Voltage 115, 0.96 Amps, 74 W Watts, 1/20 hp HP, Height (In.) 9 1/8 in, Width (In.) 9 1/2 in, Depth (In.) 7 in, 3-1/8 x 8-5/8 Cut Out Required, Provides Positive Draft for Smokepipe and Aids Proper Exhaust of Combustion Gas., Construction Material Aluminized Steel Housing and Blower Wheel, Agency Compliance -, Replaces -, View Catalog Page For Selection Criteria, Not Applicable, N/A, N/A., Not Applicable, Not Applicable, 190246259217

Barometric Draft Control, Diameter 7 in to 8 in, Galvanized Steel, Nominal Capacity 50.3, Silver, Length 2 5/8 in, Width 8 11/16 in, Height 8 11/16 in, Application Gas

Toilets and Urinals

ECM Direct Drive Blower Motor, Single Phase, Motor Design ECM, 3/4 HP, Nameplate RPM 1, 075, No. of Speeds 5, Voltage 208-230V AC, Full Load Amps 6.0, 48 Frame, Usable @ 208V Yes, Usable @ 200V No, Motor Thermal Protection None, 60 Hz, Motor Service Factor 1, Ins. Class B, Motor Shaft Rotation CW/CCW, Max. Ambient Temp. 40 Degrees C, Duty Cycle Continuous, Lead Length 42 in, Motor Enclosure Design Open Air-Over, Motor Mounting Type Round Base, Motor Mounting Position Horizontal

HVAC Motor, Single Phase, Motor Design Permanent Split Capacitor, 1/20 HP, Nameplate RPM 1, 550, No. of Speeds 1, Voltage 208-230V AC, Full Load Amps 0.40-0.38, 3.3 in Frame, Usable @ 208V Yes, Usable @ 200V No, Motor Thermal Protection Auto, 60/50 Hz, Motor Service Factor 1, Ins. Class B, Motor Shaft Rotation CW/CCW, Max. Ambient Temp. 40 Degrees C, Duty Cycle Continuous, Motor Enclosure Design Open Air-Over, Motor Mounting Type Stud, Motor Mounting Position All Angle, Number of Shafts 1