|
Environmentally Friendly
|
Yes
|
|
Network (RJ-45)
|
Yes
|
|
Product Type
|
Transceiver/Media Converter
|
|
Number of Network (RJ-45) Ports
|
2
|
|
Maximum Distance Supported
|
12.43 Mile
|
|
Network Technology
|
1000Base-BX, 1000Base-T
|
|
Number of SC Ports
|
1
|
|
Package Contents
|
SMI-1000-S1SC20D Gigabit Ethernet Media Converter, DC Adapter
|
|
Management Port
|
Yes
|
|
Total Number of Ports
|
2
|
|
Form Factor
|
Rack-mountable, Rail-mountable, Wall Mountable
|
|
Product Name
|
SMI-1000-S1SC20D Gigabit Ethernet Media Converter
|
|
Weight (Approximate)
|
1.59 lb
|
|
Current
|
0.42amps at 12vdc
|
|
Electrical Safety
|
UL 60950-1
|
|
Power / TST
|
This green LED is turned on when power is applied to the media converter. Otherwise it is off. The LED will blink when in Loopback test mode.
|
|
Operating Humidity
|
5% to 90% non-condensing
|
|
Reset button
|
Recessed pinhole button resets module
|
|
Fiber Fault Alert
|
The Fiber Fault Alert switch has meaning when Auto-Negotiation is disabled; Enabled (Default - Up); When the 1000Base-X receiver is off the 1000Base-X transmitter is turned off. Periodically the 1000Base-X receiver will be turned on for a short period to allow the condition to clear if the 1000Base-X link partner is using a similar feature; Disabled (Down)
|
|
Bit Error Rate (BER)
|
<10-12
|
|
100/1000
|
Green - 1000 Mbps link; Yellow - 100 Mbps link; Off - 10 Mbps or no Link
|
|
Copper link on / Receive activity (LKC)
|
This green LED is operational only when power is applied. The LED is on when the 1000Base-T link is on and flashes with a 50% duty cycle when data is received. The LED will slow blink when the 1000Base-T interface has been taken down as a result of a fault on the 1000Base-T interface.
|
|
1000Base-T
|
RJ45 connector, 4 pair CAT5 UTP cable or better; Magnetic Isolation - 1.5kv
|
|
Storage Humidity
|
5% to 95% non-condensing
|
|
Fiber link on / Receive activity (LKF)
|
This green LED is operational only when power is applied. The LED is on when the 1000Base-X link is on and flashes with a 50% duty cycle when data is received. The LED will slow blink when the 1000Base-X interface has been taken down as a result of a fault on the 1000Base-T interface.
|
|
Emissions
|
FCC Part 15 Class A, EN55022 Class A
|
|
Heat Output ( BTU/HR )
|
17
|
|
Duplex
|
Full (Default-Up)- The media converter will advertise Full Duplex Capable, Half Duplex Capable; AUTO (Down)-The media converter will advertise Full Duplex Not Capable, Half Duplex Capable.
|
|
Operating temperature
|
0° C to 50° C (32° F to 122° F)
|
|
Management ethernet port
|
10/100/1000Base-T - RJ45; Auto- MDI/MDIX
|
|
Immunity
|
EN55024
|
|
Universal AC/DC adapter
|
100-240v AC, regulated DC adapter included
|
|
Power Connector
|
5.5mm x 9.5mm x 2.1mm barrel socket
|
|
Chassis
|
Metal with an IP20 ingress protection rating
|
|
LKC
|
Green indicator indicating an active Ethernet link. Blinking indicates RX and TX of data
|
|
Storage temperature
|
minimum range of -25° C to 70° C (-13° F to 158° F)
|
|
Power Consumption
|
4.98watts
|
|
Auto-Negotiation
|
Enabled (Default - Up)In this mode the 1000Base-X and the 1000Base-T will negotiate to the HCD of the two link partners. The 1000Base-X will link up after the negotiation is completed and the 1000Base-T has linked up; Disabled- The 1000Base-X will not use auto negotiation. The 1000Base-T will negotiate to the HCD of the Switch settings and the link partner.
|
|
Pause
|
When Fiber Auto Negotiation is disabled Pause should only be enabled when all devices connected to the media converter support pause; Enabled(Default)- The Media converter will advertise Pause capable, Asymmetric pause not needed during Auto-Negotiation; Disabled- The Media converter will advertise that it does not have Pause capability during Auto-Negotiation.
|
|
Laser Safety
|
EN 60825-1:2007
|
|
Remote Loopback
|
The media converter can perform a loopback on the 1000Base-X fiber interface; Disabled (Default - Up); Enabled- The 1000Base-X receiver is looped to the 1000Base-X transmitter. The 1000Base-T transmitter is taken off the interface.
|
|
Management console port
|
RS232 Serial RJ45 - Cisco pinout for use with standard CAT5 "rolled cable" (crossover) 9600 to 115k bps 7/8 bits Odd,even, no parity 1/2 stop bits Hardware/software flow control DCD/DSR monitoring
|
|
Power
|
Blinking green during startup cycle Steady green: module has power and is ready; Red : error
|
|
Input Supply Voltage
|
( 12 vDC Nominal )
|
|
ALM
|
Red alarm indicator activated when an alert event occurs
|
|
Operating Altitude
|
Up to 3,048 meters (10,000 feet)
|
