- Ethernet Technology
- Gigabit Ethernet
- Weight (Approximate)
- 1.59 lb
- Maximum Distance Supported
- 328.08 ft
- Number of Network (RJ-45) Ports
- 1
- Media Type Supported
- Twisted Pair, Optical Fiber
- Network (RJ-45)
- Yes
- Network Technology
- 1000Base-TX, 1000Base-ZX
- Product Name
- SMI-1000-SFP - Gigabit Ethernet Standalone IP Managed Media Converter
- Form Factor
- Rail-mountable, Wall Mountable, Rack-mountable
- Number of Total Expansion Slots
- 1
- Expansion Slot Type
- SFP
- Number of SFP Slots
- 1
- Product Type
- Transceiver/Media Converter
- Total Number of Ports
- 1
- Environmentally Friendly
- Yes
- 1000Base-T
- RJ45 connector, 4 pair CAT 5 UTP cable or cable; Magnetic Isolation - 1.5kv
- Remote Loopback
- The media converter can perform a loopback on the 1000Base-X fiber interface; Disabled (Default - Up); Enabled- The 1000Base-X receiver is looped to the 1000Base-X transmitter. The 1000Base-T transmitter is taken off the interface.
- Laser Safety
- EN 60825-1:2007
- Current
- 0.42amps at 12vdc
- Copper link on / Receive activity (LKC)
- This green LED is operational only when power is applied. The LED is on when the 1000Base-T link is on and flashes with a 50% duty cycle when data is received. The LED will slow blink when the 1000Base-T interface has been taken down as a result of a fault on the 1000Base-T interface.
- Operating Humidity
- 5% to 90% non-condensing
- Power Connector
- 5.5mm x 9.5mm x 2.1mm barrel socket
- Reset button
- Recessed pinhole button resets module
- Dimentions
- 175 x 145 x 23 mm
- Emissions
- FCC Part 15 Class A, EN55022 Class A
- LKC
- Green indicator indicating an active Ethernet link. Blinking indicates RX and TX of data
- ALM
- Red alarm indicator activated when an alert event occurs
- Operating temperature
- 0° C to 50° C (32° F to 122° F)
- Management ethernet port
- 10/100/1000Base-T - RJ45; Auto- MDI/MDIX
- Electrical Safety
- UL 60950-1
- Fiber link on / Receive activity (LKF)
- This green LED is operational only when power is applied. The LED is on when the 1000Base-X link is on and flashes with a 50% duty cycle when data is received. The LED will slow blink when the 1000Base-X interface has been taken down as a result of a fault on the 1000Base-T interface.
- Pause
When Fiber Auto Negotiation is disabled Pause should only be enabled when all devices connected to the media converter support pause; Enabled(Default)- The Media converter will advertise Pause capable, Asymmetric pause not needed during Auto-Negotiation; Disabled- The Media converter will advertise that it does not have Pause capability during Auto-Negotiation.
- Immunity
- EN55024
- Duplex
- Full (Default-Up)- The media converter will advertise Full Duplex Capable, Half Duplex Capable; AUTO (Down)-The media converter will advertise Full Duplex Not Capable, Half Duplex Capable.
- Input Supply Voltage
- ( 12 vDC Nominal )
- Power
- Blinking green during startup cycle Steady green: module has power and is ready; Red : error
- Heat Output ( BTU/HR )
- 17
- Storage temperature
- minimum range of -25° C to 70° C (-13° F to 158° F)
- Storage Humidity
- 5% to 95% non-condensing
- Power Consumption
- 4.98watts
- Bit Error Rate (BER)
- <10-12
- 100/1000
- Green - 1000 Mbps link; Yellow - 100 Mbps link; Off - 10 Mbps or no Link
- Management console port
- RS232 Serial RJ45 - Cisco pinout for use with standard CAT5 "rolled cable" (crossover) 9600 to 115k bps 7/8 bits Odd,even, no parity 1/2 stop bits Hardware/software flow control DCD/DSR monitoring
- Operating Altitude
- Up to 3,048 meters (10,000 feet)
- Universal AC/DC adapter
- 100-240v AC, regulated DC adapter included
- Fiber Fault Alert
The Fiber Fault Alert switch has meaning when Auto-Negotiation is disabled; Enabled (Default - Up); When the 1000Base-X receiver is off the 1000Base-X transmitter is turned off. Periodically the 1000Base-X receiver will be turned on for a short period to allow the condition to clear if the 1000Base-X link partner is using a similar feature; Disabled (Down)
- Auto-Negotiation
Enabled (Default - Up)In this mode the 1000Base-X and the 1000Base-T will negotiate to the HCD of the two link partners. The 1000Base-X will link up after the negotiation is completed and the 1000Base-T has linked up; Disabled- The 1000Base-X will not use auto negotiation. The 1000Base-T will negotiate to the HCD of the Switch settings and the link partner.
- Power / TST
- This green LED is turned on when power is applied to the media converter. Otherwise it is off. The LED will blink when in Loopback test mode.
Create Account
