- MFR #
- 4JMV3
- Zoro #
- G0716143
- UPC #
- 190735326589
- Country of Origin
- China
- Item
- Centrifugal Pump
- HP
- 1/2 hp
- Housing Material
- 304 Stainless Steel
- Phase
- Single
- Voltage
- 115/230
- Max. GPM @ Head
- 38 gpm @ 5 ft
- Max. Head
- 50 ft
- Inlet
- 3/4 in NPT
- Best Efficiency GPM @ Head
- 28 gpm @ 22 ft
- Outlet
- 3/4 in NPT
- Motor Enclosure
- Open Drip Proof
- Bearing Type
- Ball
- NEMA/IEC Frame
- 56J
- Duty
- Continuous
- Motor RPM
- 3,450 RPM
- Motor Type
- Permanent Split Capacitor
- Application
- Chemical Processing, Circulation, Cooling, Liquids Transfer, Pressure Boosting and Circulating
- Drain Plug
- No
- Port Rotation
- 90 Degrees Increments
- Impeller Type
- Closed
- Max. Fluid Viscosity
- 31 SUS
- Inlet Pressure
- 128 psi
- GPM of Water @ 5 Ft. of Head
- 38
- Wetted Materials
- 304 Stainless Steel, Carbon, Ceramic, Viton
- Amps
- 7.2/3.6
- Seal Type
- Mechanical
- GPM of Water @ 25 Ft. of Head
- 26
- Impeller Material
- 304 Stainless Steel
- Shaft Material
- Stainless Steel
- GPM of Water @ 40 Ft. of Head
- 5
- Min. GPM @ Head
- 5 gpm @ 40 ft
- Service Factor
- 1.5
- Best Efficiency Range GPM @ Head
- 24 to 33 gpm @ 28 to 12 ft
- GPM of Water @ 10 Ft. of Head
- 34
- Seal Material
- Carbon, Ceramic, Stainless Steel, Viton
- Agency Compliance
- CUS
- GPM of Water @ 30 Ft. of Head
- 20
- Max. Specific Gravity
- 1.0
- GPM of Water @ 20 Ft. of Head
- 29
- GPM of Water @ 15 Ft. of Head
- 32
- Max. Liquid Temp.
- 200 Degrees F
- Max. Case Pressure
- 150 psi
- Hz
- 60
- Includes
- Manual
- Screw Material
- Stainless Steel
- Volute Material
- 304 Stainless Steel
- Standards
- CUS
- Compatible Motor Frame
- 56J NEMA
- Flow Rate @ 15 ft of Head (Maximum)
- 32 gpm
- Priming
- Manual
- Discharge Pipe Type
- NPT
- Viscosity (Maximum)
- 31 SUS
- Current
- 7.2 or 3.6 A
- Media Temperature (Maximum)
- 200 Degrees F
- Discharge Rotation
- 90 Degrees Increments
- Specific Gravity (Maximum)
- 1
- Flow Rate @ 1 ft of Head (Maximum)
- 36.5 gpm
- Wetted Material
- 304 Stainless Steel, Carbon, Ceramic, Viton
- Flow Rate (Maximum)
- 38 gpm
- Ambient Temperature (Minimum)
- 40 Degrees F
- Feet of Head (Maximum)
- 50 ft
- Ambient Temperature (Maximum)
- 104 Degrees F
- Horsepower (Maximum)
- 1/2 hp
- Shut Off Pressure (Maximum)
- 150 psi
- Motor Speed (Maximum)
- 3,450 RPM
- Impeller Design
- Closed
- Media Temperature (Minimum)
- 40 Degrees F
- Flow Rate @ 40 ft of Head (Maximum)
- 5 gpm
- Frequency
- 60 Hz
- Flow Rate (Minimum)
- 5 gpm
- Intake Pipe Type
- NPT
- Flow Rate @ 5 ft of Head (Maximum)
- 35.5 gpm
- Best Efficiency Flow
- 28 gpm
- Flow Rate @ 10 ft of Head (Maximum)
- 34 gpm
- Case Pressure (Maximum)
- 150 psi
- Flow Rate @ 20 ft of Head (Maximum)
- 29 gpm
- Best Efficiency Head
- 22 ft
- Duty Cycle
- Continuous
- Nameplate Voltage
- 115/230V AC
- For Use With Potable Systems
- No
- Flow Rate @ 30 ft of Head (Maximum)
- 20 gpm
- Flow Rate @ 25 ft of Head (Maximum)
- 26 gpm
- Discharge Position
- Offset
- Case Pressure - Maximum
- 150 psi
- Pump Housing Material
- Stainless Steel
- Discharge Orientation
- Side
- Drive Coupling Type
- No Coupling
- Shaft Seal Type
- Mechanical
- Pump Design
- End Suction
- Motor Design
- Permanent Split Capacitor
- Shaft Seal Material
- Carbon/Ceramic, FKM, Stainless Steel
- Thermal Overload Protection
- Yes
- Ambient Temperature - Minimum
- 40 Degrees F
- Horsepower
- 1/2 hp
- Inlet Orientation
- Side
- Discharge Rotation Increments
- 90 Degrees
- Flow Rate @ 10 ft of Head - Maximum
- 34 gpm
- Inlet Position
- Center
- Full Load Current
- 7.2/3.6
- Hazardous Location Class
- Not Rated
- Shut Off Pressure - Maximum
- 150 psi
- Media Temperature - Minimum
- 40 Degrees F
- Motor Speed - Maximum
- 3,450 RPM
- Feet of Head (Minimum)
- 0 ft
- Media Temperature - Maximum
- 200 Degrees F
- Mounting Orientation
- Horizontal
- Number of Stages
- 1
- Chemical Compatibility
- Non-Abrasive Liquids, Non-Flammable Liquids
- Ambient Temperature - Maximum
- 104 Degrees F
- NPSHr
- 1.95 ft
Create Account