For Use With Anti-Freeze, Clean Water, Diesel Exhaust Fluid
Item Electric Drum Pump
Includes Nozzle Holder, Spring Loaded Drum Mounting Bracket
Max. Viscosity 10 cps
Motor Type 2 Pole
Power Source Corded Electric
Wetted Materials EPDM, Polypropylene, Stainless Steel
Voltage 12VDC
Motor Enclosure IP55
Metered Yes
Motor RPM 2,600 RPM
Max. Temp. 104 Degrees F
DEF Compatible Yes
Standards ISO
RPM 1730
Housing Material Polypropylene
Max. Liquid Temp. 104 Degrees F
Max. GPM for Water 8
Hose Material Peroxide Cured EPDM
Max. Head 48 ft.
GPM 8
Agency Compliance ISO
Application Diesel Exhaust Fluid, Anti-Freeze, Clean Water
Pump Body Material Polypropylene, EPDM
Gasket Material EPDM
HP 1/10
pH Range 9.8 to 10
Phase Single
Max. Pressure 23 psi
Seal Material EPDM
Max. Fluid Temp. 104 Degrees F
Suction Tube ID 3/4 in
Includes Nozzle Yes
Discharge Tube Outlet ID 3/4 in
Hose Cover Material Thermal Plastic Not Recommended Chemicals
See full list of Not Recommended Chemicals Acetic Acid 80%,Acetone,Ammonia Liquid,Anhydrous Ammonia,Automatic Transmission Fluid,Biodiesel,Brake Fluid,Calcium Chloride,Chromic Acid 10%,Chromic Acid 30%,Chromic Acid 5%,Chromic Acid 50%,Concentrated Nitric Acid,Cyclohexane,Diesel Fuel,E85,Ethyl Acetate,Fertilizers,Formic Acid,Fungicides,Gasoline,Glacial Acetic Acid,Heptane,Herbicides,Hexane,Petroleum Oil,Synthetic Oil,Hydrazine,Hydrochloric Acid 100%,Hydrochloric Acid 20%,Hydrochloric Acid 37%,Hydrofluoric Acid 100%,Hydrofluoric Acid 20%,Hydrofluoric Acid 75%,Kerosene,Lacquer Thinners,Lithium Grease,Methanol,Methyl Chloride,Methyl Ethyl Ketone,Motor Oil,Naphtha,Nitric Acid 10% Solution,Nitric Acid 20% Solution,Nitric Acid 50% Solution,Paint,Paint Thinner,Pesticides,Phosphoric Acid 40% Solution,Sodium Bisulfate,Sodium Hydroxide 20%,Sodium Hydroxide 50%,Sodium Hydroxide 80%,Stoddard Solvent,Sulfuric Acid 10% to 75%,Sulfuric Acid 75% to 100%,Sulfuric Acid up to 10%,Toluene,Trichlorethylene 50%,Turpentine,Windshield Washer Fluid,Xylene
Includes Bung Adapter No
Full Load Amps 22.0 A
Housing Material - Pumps Polypropylene
Hose Tube Material EPDM
Nozzle Material Stainless Steel
Includes Discharge Hose Yes
Spout Material 316 Stainless Steel
Runs Dry Yes
For Container Type Drum, Tote
Max. Oil Flow 8 gpm
Food Grade No
For Media Type Acetic Acid, Ammonium Hydroxide, Antifreeze, Bleach, Citric Acid, DEF, Ethanol, Ethylene Glycol, Formaldehyde, Glycerin, Isopropanol, Potassium Hydroxide (50%), Sodium Bicarbonate, Sodium Bisulfite, Water
Motor HP 1/10 hp
Plug Type Spring Clamp Compatible Chemicals
See full list of Compatible Chemicals Acetic Acid 20%,Ammonium Hydroxide,Antifreeze (Coolant),Citric Acid 50%,DEF,Deionized Water,Ethyl (Ethanol),Ethylene Glycol,Formaldehyde,Formaldehyde 40%,Fresh Water,Glycerin,Isopropyl (Isopropanol),Potassium Hydroxide (50%),Salt Water,Sodium Bicarbonate (10%),Sodium Bisulfite,Sodium Hypochlorite/Bleach (to 20%)
Variable Speed No
Discharge Tube Outlet OD 1 in
Diesel Exhaust Fluid Compatible Yes
Suction Tube Material EPDM
Min. Fluid Temp. 17 Degrees F
Includes Spout Yes
Max. Flow Rate 8 gpm
Pump Connection OD 1 in
Nozzle Operation Automatic
Spout Connection Type Integral to Nozzle
Pump Connection Type Hose Barb
Discharge Connection Type Hose Barb
Self-Priming Yes
Number of Phases 1
Max. Head - Pumps 48 ft
Max. Head Pressure 23 psi
Includes Suction Tube Yes
Suction Tube OD 1 in
Noise Level 70 dB
Duty Cycle Intermittent
Max. Outlet Pressure 23 psi
Gear Lube NT
Rated Voltage 12 V DC
Grease NT
Explosion Proof No
Maximum Outlet Pressure 23 psi
Maximum Head Pressure 23 psi
Maximum Oil Flow 8 gpm
Maximum Head 48 ft
Static Protection Not Groundable
Motor Enclosure Design Totally Enclosed Non-Ventilated
Meter Unit Of Measure Gallons, Liters
Full Load Current 22 A
Motor Horsepower 1/10 hp
Pump Connection ID 3/4 in
Wetted Material EPDM/Polypropylene/Stainless Steel
Minimum Fluid Temperature 17 Degrees F
Housing Finish Powder Coated
Chemical Compatibility Acetic Acid 20%, Ammonium Hydroxide, Antifreeze Coolant, Bleach, Citric Acid 50%, DEF, Deionized Water, Ethanol, Ethylene Glycol, Formaldehyde, Formaldehyde 40%, Fresh Water, Glycerin, Isopropanol, Potassium Hydroxide 50%, Salt Water, Sodium Bicarbonate 10%, Sodium Bisulfite
Maximum Flow Rate 8 gpm
Nozzle Fluid Compatibility DEF
Hazardous Location Class Not Rated
Meter Type Included Digital
Mount Type Foot
Maximum Viscosity 10 cps
Pump Technology Diaphragm
Motor Speed 2,600 RPM
Maximum Fluid Temperature 104 Degrees F
Adapter Connection Standard Buttress
Power Source - TS Only Corded Electric 
Create Account
