For Use With Anti-Freeze, Clean Water, Diesel Exhaust Fluid
Item Electric Drum Pump
Includes Coupler, Drip Cup, Hose, Nozzle Hanger, Side Mount Hanger
Max. Viscosity 10 cps
Motor Type 2 Pole
Power Source Corded Electric
Wetted Materials EPDM, Polypropylene, Stainless Steel
Voltage 115VAC
Motor Enclosure IP55
Metered Yes
Motor RPM 1,750 RPM
Max. Pressure 33 psi
Amps 3.5
Max. Temp. 104 Degrees F
Duty Cycle Intermittent
Features Dispenses 8 gpm
Suction Lift 6 ft.
Pump Design Nutating Diaphragm
Transfer Pump Application Agriculture, Automotive, Construction, Farming, Industrial, Marine, Trucking
pH Range 5.0 to 10
Nozzle Material Polypropylene/Stainless Steel
Max. Specific Gravity 1.09
Nozzle Type Manual
HP 1/10
Hose Material Peroxide Cured EPDM
Max. Head 48 ft.
Phase Single
Seal Material EPDM
Gasket Material EPDM
Shaft Material Stainless Steel
Bearing Type Sealed Ball
Agency Compliance ISO
Hz 60
Max. GPM for Water 8
Self-Priming Yes
Pump Body Material Polypropylene
GPM 8
Pressure Range 23 psi
Inlet 3/4"
Max. Liquid Temp. 104 Degrees F
Seal Type Mechanical
Adapter Type RSV
Application Diesel Exhaust Fluid, Anti-Freeze, Clean Water
Duty Intermittent
Adapter Material 316 Stainless Steel
Housing Material Polypropylene
Bypass Valve Internal
Suction Tube Material EPDM
Full Load Amps 4.5 A
Housing Material - Pumps Polypropylene
Discharge Tube Outlet OD 1 in
Max. Fluid Temp. 104 Degrees F
Hose Tube Material EPDM
Max. Oil Flow 8 gpm
For Media Type Acetic Acid, Ammonium Hydroxide, Antifreeze, Bleach, Citric Acid, DEF, Ethanol, Ethylene Glycol, Formaldehyde, Glycerin, Isopropanol, Potassium Hydroxide (50%), Sodium Bicarbonate, Sodium Bisulfite, Water
Suction Tube ID 3/4 in
Frequency (Hz) 60 Hz
Noise Level 70 dB
Max. Head Pressure 23 psi
Includes Suction Tube Yes
Nozzle Operation Manual
Includes Spout Yes
Food Grade No
Number of Phases 1
Diesel Exhaust Fluid Compatible Yes
For Container Type Drum, Tote
Pump Connection Type Hose Barb
Spout Material 316 Stainless Steel
Pump Connection OD 1 in
Runs Dry Yes
Includes Bung Adapter No
Spout Connection Type Integral to Nozzle
Hose Cover Material Thermal Plastic
Min. Fluid Temp. 17 Degrees F
Includes Discharge Hose Yes Compatible Chemicals
See full list of Compatible Chemicals Acetic Acid 20%,Ammonium Hydroxide,Antifreeze (Coolant),Citric Acid 50%,DEF,Deionized Water,Ethyl (Ethanol),Ethylene Glycol,Formaldehyde,Formaldehyde 40%,Fresh Water,Glycerin,Isopropyl (Isopropanol),Potassium Hydroxide (50%),Salt Water,Sodium Bicarbonate (10%),Sodium Bisulfite,Sodium Hypochlorite/Bleach (to 20%)
Max. Head - Pumps 48 ft Not Recommended Chemicals
See full list of Not Recommended Chemicals Acetic Acid 80%,Acetone,Ammonia Liquid,Anhydrous Ammonia,Automatic Transmission Fluid,Biodiesel,Brake Fluid,Calcium Chloride,Chromic Acid 10%,Chromic Acid 30%,Chromic Acid 5%,Chromic Acid 50%,Concentrated Nitric Acid,Cyclohexane,Diesel Fuel,E85,Ethyl Acetate,Fertilizers,Formic Acid,Fungicides,Gasoline,Glacial Acetic Acid,Heptane,Herbicides,Hexane,Petroleum Oil,Synthetic Oil,Hydrazine,Hydrochloric Acid 100%,Hydrochloric Acid 20%,Hydrochloric Acid 37%,Hydrofluoric Acid 100%,Hydrofluoric Acid 20%,Hydrofluoric Acid 75%,Kerosene,Lacquer Thinners,Lithium Grease,Methanol,Methyl Chloride,Methyl Ethyl Ketone,Motor Oil,Naphtha,Nitric Acid 10% Solution,Nitric Acid 20% Solution,Nitric Acid 50% Solution,Paint,Paint Thinner,Pesticides,Phosphoric Acid 40% Solution,Sodium Bisulfate,Sodium Hydroxide 20%,Sodium Hydroxide 50%,Sodium Hydroxide 80%,Stoddard Solvent,Sulfuric Acid 10% to 75%,Sulfuric Acid 75% to 100%,Sulfuric Acid up to 10%,Toluene,Trichlorethylene 50%,Turpentine,Windshield Washer Fluid,Xylene
Suction Tube OD 1 in
Includes Nozzle Yes
Discharge Connection Type Hose Barb
Discharge Tube Outlet ID 3/4 in
Max. Flow Rate 8 gpm
Motor HP 1/10 hp
Variable Speed No
Gear Lube NT
Explosion Proof No
Max. Outlet Pressure 23 psi
Rated Voltage 115 V AC
Grease NT
Mount Type Foot
Hazardous Location Class Not Rated
Housing Finish Powder Coated
Plug Type NEMA 5-15-P
Maximum Head Pressure 23 psi
Maximum Head 48 ft
Maximum Viscosity 10 cps
Maximum Oil Flow 8 gpm
Standards ISO
Motor Horsepower 1/10 hp
Motor Enclosure Design Totally Enclosed Fan Cooled
Maximum Flow Rate 8 gpm
Nozzle Fluid Compatibility DEF
Full Load Current 4.5 A
Maximum Outlet Pressure 23 psi
Meter Type Included No Meter Included
Pump Technology Diaphragm
Chemical Compatibility Acetic Acid 20%, Ammonium Hydroxide, Antifreeze Coolant, Bleach, Citric Acid 50%, DEF, Deionized Water, Ethanol, Ethylene Glycol, Formaldehyde, Formaldehyde 40%, Fresh Water, Glycerin, Isopropanol, Potassium Hydroxide 50%, Salt Water, Sodium Bicarbonate 10%, Sodium Bisulfite
Minimum Fluid Temperature 17 Degrees F
Pump Connection ID 3/4 in
Frequency 60 Hz
Static Protection Not Groundable
Maximum Fluid Temperature 104 Degrees F
Wetted Material EPDM/Polypropylene/Stainless Steel
Adapter Connection Standard Buttress
Motor Speed 1,750 RPM
Power Source - TS Only Corded Electric 
Create Account
