- Item
- Magnetic Drive Pump
- HP
- 1/25 hp
- Voltage
- 115
- Inlet
- 1/2 in MPT
- Outlet
- 1/2 in MPT
- Max. Head
- 16.2 ft
- Housing Material
- Glass-Filled Polyphenylene
- Full Load Amps
- 1.4 A
- Gasket Material
- FKM
- Mounting
- Horizontal
- GPM of Water @ 3 Ft. of Head
- 7.6 gpm
- Temp. @ 0 psig
- 180 Degrees F
- Cord Type
- 3-conductor SJO
- GPM of Water @ 9 Ft. of Head
- 5.9 gpm
- Temp. @ 20 psig
- 145 Degrees F
- Max. Specific Gravity
- 1.1
- Motor Type
- Shaded Pole
- Temp. @ 10 psig
- 165 Degrees F
- Impeller Material
- Carbon/Polyphenylene
- GPM of Water @ 6 Ft. of Head
- 7.1 gpm
- Design
- Gravity-feed, Requires the Pump Inlet to be Lower than Liquid Level
- Max. Viscosity
- 100 SSU
- Application
- For Highly Corrosive Chemicals, Eliminates Seal-caused Friction Loss, Wear, Contamination and Leakage
- Bearing Type
- Thrust
- Temp. @ 30 psig
- 135 Degrees F
- Series
- MD-HC
- GPM of Water @ 15 Ft. of Head
- 1.7 gpm
- Motor Enclosure
- Open Air Over
- Discharge Pipe Type
- NPT
- Viscosity (Maximum)
- 100 SUS
- Flow Rate @ 9 ft of Head (Maximum)
- 5.9 gpm
- Flow Rate @ 6 ft of Head (Maximum)
- 7.1 gpm
- Motor Mounting Type
- Horizontal
- Specific Gravity (Maximum)
- 1.1
- Media Temperature (Maximum)
- 200 Degrees F
- Nameplate Voltage
- 115V AC
- Frequency
- 60 Hz
- Operating Pressure (Maximum)
- 7.01 psi
- Full Load Current
- 1.3 A
- Horsepower (Maximum)
- 1/25 hp
- Feet of Head (Maximum)
- 16.2 ft
- Flow Rate @ 3 ft of Head (Maximum)
- 7.6 gpm
- Phase
- Single
- Ambient Temperature (Maximum)
- 77 Degrees F
- Flow Rate @ 15 ft of Head (Maximum)
- 1.7 gpm
- Intake Pipe Type
- MNPT
- Pumping Application
- Chemical Transfer
- Drive Coupling Type
- Magnetic Coupling
- Ambient Temperature - Maximum
- 77 Degrees F
- Flow Rate (Maximum)
- 8.5 gpm
- Number of Stages
- 1
- Media Temperature - Minimum
- 32 Degrees F
- Mounting Orientation
- Horizontal
- Best Efficiency Head
- 10 ft
- Pump Drive Configuration
- Close-Coupled
- Media Temperature - Maximum
- 200 Degrees F
- Shaft Seal Type
- Sealless
- Ambient Temperature - Minimum
- 32 Degrees F
- Hazardous Location Class
- Not Rated
- Case Pressure - Maximum
- 7 psi
- Priming
- Manual
- Chemical Compatibility
Acetylene,Acid,Alcohol,Aluminum Chloride,Aluminum Chloride 20%,Aluminum Sulfate,Ammonium Chloride,Ammonium Hydroxide,Antifreeze,Barium Chloride,Barium Hydroxide,Barium Sulfate,Benzene,Borax,Butadiene,Butane,Butylene,Calcium Chloride,Calcium Sulfate,Carbon Disulfide,Chlorobenzene,Copper Cyanide,Copper Sulfate 5%,Cyclohexane,Diesel Fuel,Distilled,Ethyl Chloride,Ethylene Chloride,Ethylene Glycol,Ferric Chloride,Ferrous Chloride,Ferrous Sulfate,Formic Acid,Fuel Oil,Gasoline,Heptane,Hexane,Jet Fuel,Kerosene,Lactic Acid,Lubricants,Magnesium Hydroxide,Magnesium Sulfate,Mine,Naphtha,Naphthalene,Cotton Seed Oil,Mineral Oil,Perchloroethylene,Plating Solutions,Potassium Bicarbonate,Potassium Carbonate,Potassium Chlorate,Potassium Chloride,Potassium Dichromate,Potassium Permanganate,Potassium Sulfate,Salt,Soap,Sodium Aluminate,Sodium Bicarbonate,Sodium Bisulfate,Sodium Bisulfite,Sodium Carbonate,Sodium Chlorate,Sodium Chloride,Sodium Chromate,Sodium Cyanide,Sodium Sulfate,Sodium Sulfide,Sodium Thiosulphate,Stoddard Solvent,Sulfuric Acid 10% to 75%,Sulfuric Acid 1% to 10%,Tomato Juice,Turpentine,Vinegar,Water,Xylene,Zinc Chloride,Zinc Sulfate
- Best Efficiency Flow
- 5 gpm
- Pump Design
- End Suction
- Shut Off Pressure - Maximum
- 7 psi
- Pump Mounting Style
- Base-Mounted
Create Account
